10 ADAPTERS
Inlet
Offset Bevel Seal Inlet Adapters A unique glass adapter offset and angled approximately 10° for use with multi-neck flasks.
Bleed Type Inlet Adapters Liquids or gases may be directed into organic reactions using this adapter.
•
Thermometers or bleed tubes are angled into the bottom of a flask A vacuum-tight seal is created with the open top compression cap and FKM o-ring to allow adjustable immersion of thermometers
•
Inlet adapter may also be calibrated and used as a pipet Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type I, Class A requirements
•
•
• •
Cap is suitable for use to 150 °C
Supplied complete with one size 010 FKM o-ring and one 410119 cap Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type I, Class A requirements
Overall Length (mm)
Part Number
OD (mm)
Case Qty
•
273410-0000
280
6.5
1
Standard Taper Joints
Part Number
O-Ring Size Case Qty
Bleed Type Inlet Adapters with Hose Connection For the introduction of gases or liquids during reactions.
179710-2114 179710-2119 179710-2124
14/20 19/22 24/40
10 10 10
1 1 1
• •
Hose connection fits ¼” ID flexible tubing
Offset Bevel Seal Inlet Adapters
With Septum
Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type I, Class A requirements
Typical Setup
Fits Tubing ID (inches)
Part Number
Overall Height (mm) Case Qty
275501-0000
1/4
135
1
Bevel Seal Inlet Adapters For use with plain thermometers, pipets, syringes or other small items with an OD from 2 to 17 mm.
Bleed Type Inlet Adapters with Top Tubulature For the introduction of gases or liquids to reactions.
•
A vacuum-tight seal is created with the open top compression cap and FKM o-ring to allow adjustable immersion of thermometers
•
Cap is suitable for use to 150 °C
• •
Fits 10 mL round bottom flasks with a 10/18 joint Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type I, Class A requirements
• To use it as a septum port, just replace the o-ring with a PTFE-lined septum • Supplied with one FKM o-ring and one 410119 cap • Ref: ASTM Method D1744 • Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type I, Class A requirements
Length Below Joint (mm)
Part Number
Top
Case Qty
10/18 Standard Taper with Top Tubulature
275400-0035
35
1
O-Ring Size/ Accommodation Range (mm)
Standard Taper Joints
Part Number
Case Qty
746030-0510 179700-0514 746030-0000 179700-2114 179700-0814 179700-0519 179700-2119 179700-0819 179700-1119 179700-0524 179700-2124 179700-0824 179700-1124 179700-1424 179700-0529 179700-2129 179700-1729
14/10 14/20 14/10 14/20 14/20 19/22 19/22 19/22 19/22 24/40 24/40 24/40 24/40 24/40 29/42 29/42 29/42
105, 2-5 105, 2-5
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Bleed Type Inlet Adapters with Hose Connection and Standard Taper Joint Used to introduce reactants below the liquid surface.
010, 5.5-6.5 010, 5.5-6.5
108, 5-8 105, 2-5
010, 5.5-6.5
•
Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type I, Class A requirements
108, 5-8 111, 8-11 105, 2-5
010, 5.5-6.5 108, 5-8 111, 8-11 113, 11-14
Standard Taper Joints
Bottom Tube Length (mm)
Part Number
Case Qty
275600-0000 179000-2440
14/20 24/40
75
1 1
105, 2-5
200
010, 5.5-6.5 207, 14-17
Powered by FlippingBook